ZEBRA STRIPE S600 DRIVERS FOR WINDOWS

Automotive

Comments to this Manuals Your Name. Zebra recommends performing the cleaning procedure when installing a new roll of ribbon, when installing a new roll of direct thermal media, or after having printed feet m of continuous or fanfold media. Contrast this with fanfold media, which comes folded in a rectangular stack. The printer first runs through a Power-On Self Test, then prints the configuration label. Table Of Contents Printing Considerations

Uploader: Diran
Date Added: 8 November 2006
File Size: 61.86 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 56967
Price: Free* [*Free Regsitration Required]

Tear-Off mode, skip to step 6. Some commercially available lubricants will damage the finish if used. Slide the ribbon supply spindle subassembly zebra stripe s600 the shaft.

Page Carefully pry the front of the power supply base downward to remove zebra stripe s600 assembly. Enter text from picture: Page 40 a to remove it from the mating socket on the cutter module. Page 51 Remember to remove each label as it is automatically peeled away from the backing. Pivot the board off the front snaps.

Oltec Pacific Center Pte Ltd

Cutter option not installed Check cutter configuration. Pause Key Self Test In the Peel-Off mode, proper media tracking is critical.

Page 12 Cutter mode.

Page It is not necessary to remove the main door or the front door if installing only the memory upgrade kit. If you discover shipping damage: Side View of Cutter Zebra stripe s600 Reassembly Page Remove the main logic board and media sensor assembly. By pressing ‘print’ button stipe will print only current page.

Oltec Pacific Center Pte Ltd

Troubleshooting Chart Settings or Parameter-Related Page tsripe the base. Page 31 pin parallel connector on one end, which is plugged into the mating connector located inside the access opening on the zebra stripe s600 side of the printer. Test, Formats 2 and 9 L Rev. Zebra recommends performing the cleaning procedure when installing a new roll of ribbon, when installing a new roll of direct thermal media, or after having zebra stripe s600 feet zevra of continuous or fanfold media.

Calibrate, position, darken, data, and pause Firmware error. Remove the three mounting screws from the memory board and put aside zebra stripe s600 zdbra later.

If error condition persists after attempting each of the above solutions, call a service technician. Carefully pry the front of the power supply base downward to remove the assembly.

Zebra Stripe S400 User Manual

Page 77 To ensure the printer has proper ventilation and cooling, do not zebra stripe s600 any padding or cushioning material under the unit because this restricts air flow. Two or three blank labels feed, completing auto calibration. Zebra stripe s600 Guides Platen Roller Bearings pictured here are installed this way for the only. Comments to this Manuals Your Name. These guides must not cause pressure or excessive drag on the media. For very narrow media, zero pressure from the right toggle may be required.

PSFLA shall continue in full force and effect. Peel-Off Option Front View Peel Option and Peel Drive System Page Reverse the procedures to reinstall the print mechanism assembly. Refer to Figure on page The printer automatically feeds out and cuts one label when power zebra stripe s600 turned On l.

Page 76 Figure Page 33 External influences such as lightning storms or unwanted noise on the power or data cables may cause erratic printer behavior.

Media Sensor Adjustment L Rev. Cut zebra stripe s600 ribbon between the upper ribbon guide roller and the ribbon take-up spindle. Use only the cleaning agents indicated below. Tape the end of the 30″ long Mylar tape Zebra part to the rewind spindle. They should point directly at one another.

stdipe This test is performed only when sensor zebra stripe s600 are replaced or if a manual calibration fails. Autobaud only works for baud and higher. The printer is now ready to zebra stripe s600 more labels. Unless indicated otherwise, turn the power Off O before performing any maintenance procedures to the printer. FEED V the necessary number of times.

Page 13 Figure 4.